Your Cart Preview ×

You have no items in your shopping cart.

Controlis Customer Support: 1300-781-861

  • Australia wide Delivery
  • 14 Day Returns
  • Genuine Product Guarantee
insteon

DIN Rail Dimmer

DIN Rail Dimmer

More Views

Overview

Details

About INSTEON DIN-Rail Dimmer

The INSTEON DIN-Rail Dimmer module clips directly onto a 35mm DIN rail and wires to load, power and neutral.

Easily installed by a licensed electrician.

  • Simply clip onto 35mm DIN rail and wire like any other INSTEON switch
  • Optional sense wires allow for control via a connected, hard-wired switch
  • Compatible with latching, single momentary and dual momentary switches
  • Award-winning INSTEON dual-mesh technology 
Additional Information

Product Specifications

Electrical

Supply Voltage 100VAC to 240VAC (± 10%)
Frequency 50/60Hz auto-detected at power-up
Max. Load 10A, 3600W/240VAC resistive, 700W/240VAC inductive/capacitive, 2000W/240VAC bulbs
Load Types Resistive, Inductive/capacitive, Low voltage halogen
Surge Protection Over 1,000 Volts
Power Plug 2-pin Safety Shielded (Removable figure 8 power cable)
Retain all settings without power Yes, saved in non-volatile EEPROM
Standby Power Consumption < 1 watt
Battery Charge Hold Duration 9-12 months based on average 16 button presses per day (will decrease over time)
Recharging Jack Standard, Micro-USB, 5VDC
Recharging Time 1 hour
Battery Life 6 months (w/ 2 links @ 50 activations per day)
Safety Approved Approved for use in Australia and New Zealand

INSTEON

INSTEON Power line Mesh Repeater 0
INSTEON RF Mesh Repeater 0
INSTEON Controller 0
INSTEON Responder 0
Maximum Links 400
Frequency RF 921MHz ISM Band
Local on-level Adjustable from 32 fixed brightness levels or resume dim
Local ramp rate Adjustable from 0.1 second to 5 seconds locally (0.1 seconds to 8 minutes with software)
Scene Commands Supported On / Off, Fast on / Fast off, Begin brighten / End brighten, Begin dim / End dim
Status LED Red when heating, green when cooling, blinks red or green during setup
Local Control 0
Load Brightness Levels 32 locally (256 with software)
LED Brightness LED can be enabled or disabled locally or via software
INSTEON RF 0
Commands Supported as Controller On / Off
Commands Supported as Responder On / Off / Beep
Software Configurable 0
RF Range Up to 50 meters open air
X10 Support Yes (X10 address: any 1 of 256 - unassigned by default)

Product Information

Product Name INSTEON DIN-Rail Dimmer
Warranty 2 Years
In the Box INSTEON DIN-Rail Dimmer, Quick Start Guide
Product Code IN2452-522

Mechanical

Mounting Table top or wall mount
Casing UV stabalized plastic (INSTEON White)
Wire Connections Common 24V / Power 24V / Heat 1 / Heat 2 / Fan / Cooling 1 / Cooling 2
LED 1 RGB
LED During Use Green flash once (On, Bright, Fast On), Red flash once (Off, Dim, Fast Off)
Screw Clamp Connections Yes, 10 position
LED Battery Charge Indicator Built-in battery charge LED indicator
Power Switch For disabling buttons (“vacation” or “pocket” mode)
Set button 0
Sense Modes (Jumper on) Open = Group 1 On, Closed = Group 1 Off
Sense Modes (Jumper off) Open = Group 1 On (or off), Closed = Group 2 On (or Off)
Aux. Sensor Input Wire >= 20 gauge wire
Beep on button press Optional (off by default)
Stuck Button Mode Saves battery life by going to sleep if button stuck down
Beeper 0
Sensitivity Modes High (default) or Normal
Motion Detection Range Up to 110° arc, 12m
Motion Detector Sense Input Type PIR and photocell
Dimensions & Weight 80mm W x 53mm H x 63mm D - 175g
Operating Conditions Indoors, 0° C to 40° C, up to 90% relative humidity
insteon
DIN Rail Dimmer
AU$ 99
Ships in 10-12 business days

When planning the electrical wiring for your home or business, avoid adding too many wall switches in a single location. Wall switches ganged together cause confusion and can quickly ruin...

Availability: Backorder

+ -
Shop risk free with Controlis
  • 14 Day Returns
  • Australian Support
  • Fully Complaint Installers
  • 100% Secure encryption
Overview

Details

About INSTEON DIN-Rail Dimmer

The INSTEON DIN-Rail Dimmer module clips directly onto a 35mm DIN rail and wires to load, power and neutral.

Easily installed by a licensed electrician.

  • Simply clip onto 35mm DIN rail and wire like any other INSTEON switch
  • Optional sense wires allow for control via a connected, hard-wired switch
  • Compatible with latching, single momentary and dual momentary switches
  • Award-winning INSTEON dual-mesh technology 
Additional Information

Product Specifications

Electrical

Supply Voltage 100VAC to 240VAC (± 10%)
Frequency 50/60Hz auto-detected at power-up
Max. Load 10A, 3600W/240VAC resistive, 700W/240VAC inductive/capacitive, 2000W/240VAC bulbs
Load Types Resistive, Inductive/capacitive, Low voltage halogen
Surge Protection Over 1,000 Volts
Power Plug 2-pin Safety Shielded (Removable figure 8 power cable)
Retain all settings without power Yes, saved in non-volatile EEPROM
Standby Power Consumption < 1 watt
Battery Charge Hold Duration 9-12 months based on average 16 button presses per day (will decrease over time)
Recharging Jack Standard, Micro-USB, 5VDC
Recharging Time 1 hour
Battery Life 6 months (w/ 2 links @ 50 activations per day)
Safety Approved Approved for use in Australia and New Zealand

INSTEON

INSTEON Power line Mesh Repeater 0
INSTEON RF Mesh Repeater 0
INSTEON Controller 0
INSTEON Responder 0
Maximum Links 400
Frequency RF 921MHz ISM Band
Local on-level Adjustable from 32 fixed brightness levels or resume dim
Local ramp rate Adjustable from 0.1 second to 5 seconds locally (0.1 seconds to 8 minutes with software)
Scene Commands Supported On / Off, Fast on / Fast off, Begin brighten / End brighten, Begin dim / End dim
Status LED Red when heating, green when cooling, blinks red or green during setup
Local Control 0
Load Brightness Levels 32 locally (256 with software)
LED Brightness LED can be enabled or disabled locally or via software
INSTEON RF 0
Commands Supported as Controller On / Off
Commands Supported as Responder On / Off / Beep
Software Configurable 0
RF Range Up to 50 meters open air
X10 Support Yes (X10 address: any 1 of 256 - unassigned by default)

Product Information

Product Name INSTEON DIN-Rail Dimmer
Warranty 2 Years
In the Box INSTEON DIN-Rail Dimmer, Quick Start Guide
Product Code IN2452-522

Mechanical

Mounting Table top or wall mount
Casing UV stabalized plastic (INSTEON White)
Wire Connections Common 24V / Power 24V / Heat 1 / Heat 2 / Fan / Cooling 1 / Cooling 2
LED 1 RGB
LED During Use Green flash once (On, Bright, Fast On), Red flash once (Off, Dim, Fast Off)
Screw Clamp Connections Yes, 10 position
LED Battery Charge Indicator Built-in battery charge LED indicator
Power Switch For disabling buttons (“vacation” or “pocket” mode)
Set button 0
Sense Modes (Jumper on) Open = Group 1 On, Closed = Group 1 Off
Sense Modes (Jumper off) Open = Group 1 On (or off), Closed = Group 2 On (or Off)
Aux. Sensor Input Wire >= 20 gauge wire
Beep on button press Optional (off by default)
Stuck Button Mode Saves battery life by going to sleep if button stuck down
Beeper 0
Sensitivity Modes High (default) or Normal
Motion Detection Range Up to 110° arc, 12m
Motion Detector Sense Input Type PIR and photocell
Dimensions & Weight 80mm W x 53mm H x 63mm D - 175g
Operating Conditions Indoors, 0° C to 40° C, up to 90% relative humidity
People who viewed this also viewed:

  • Plug In Relay (On/Off)

    AU$69

    Was AU$ 69

  • Plug-In Dimmer

    AU$69

    Was AU$ 69

Copyright © 2016 Controlis